CB Board Schematic Diagram CG Board Schematic Diagram V Board Schematic Diagram G Board Schematic Diagram UD Board Schematic Diagram A Board Schematic Diagram 1 of A Board Schematic Diagram 2 of A Board Schematic Diagram 3 of U Board Schematic Diagram AD Board Schematic Diagram B Board Schematic Diagram 1 of B Board Schematic Diagram 2 of D Board Schematic Diagram SR Board Schematic Diagram H2 Board Schematic Diagram H1 Board Schematic Diagram H4 Board Schematic Diagram IC Block Diagrams A Board B Board CR Board CG Board CB Board U Board Cover KPWS 0nly Picture Tube High performance, large diameter hybrid lens F1.
Design and specifications are subject to change without notice. Page of Go. In the case of GRN mode 4. If any of these adjustments are off, even slightly, the auto-registration pattern will not hit the four sensors properly. You must enter PJED service mode mode, the error will be displayed in text to see the error code. Supply VAC to variable autotransformer. Receive the signal. Connect an oscilloscope between CN Actual measured value may be different.
RF Circled numbers are waveform references. If service is required, complete board replacement is the preferred repair method. Data is provided for reference only.
Items marked with an asterisk are not stocked since they are seldom required for routine service. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifie. Replace only with part number specified. Page — Page Page The model and serial numbers are located at the rear of the cabinet, unplug the projection TV immediately and projection TV, below the Sony logo, on the sticker, and have it checked by qualified service personnel before also on the TV box white label.
Record these numbers in operating it further. Carefully observe and comply with all warnings, cautions Always turn the set off when it is not and instructions placed on the set or described in the No part of the TV set should overhang any edge of Be sure the antenna system is grounded so as to provide the TV cart or stand; Page Lightning Safety Check For added protection for this television receiver during a Upon completion of any service or repairs lightning storm, or when it is left unattended and unused to the set, ask the service technician to for long periods of time, unplug it from the wall outlet perform routine safety checks as specified and disconnect the antenna.
KPWS is used for illustration purposes, unless indicated otherwise. No peripheral cables are included. If you intend to add additional equipment to your projection TV, please check the hookup instructions for your desired setup before you begin.
The projection TV has been equipped with casters for easy movement on a hard surface. Please move your projection TV using the casters. Push into connection. Pressing MENU brings up the on-screen menus. The arrow buttons move the on-screen cursor in the menus and by pressing the Select button selects the menu item. Newer homes are equipped with standard coaxial cable see A ; older homes to Cable or an probably have ohm twin lead cable see B ; Page Also, set Cable to On in the Channel menu see page Disconnect all power sources before making any connections.
Be sure to read the Using three separate component video cables, connect the Digital TV Set-top box manual. You can connect an AV receiver using both composite video and S Disconnect all power sources before making any connections.
The Auto Setup screen appears when you turn your projection TV on for the first time after installing it. If you do not want to set up the channels at this time, you can do it later by using the Auto Program feature in the Channel menu see page If they do not converge, the color is poor and the picture blurs.
Before you use your projection TV, be sure to adjust the convergence. Begin with the crosses in the center area of the screen and, once those are adjusted, move to the crosses on the edges Manually of the screen. Page Using The Features Using the Features Using the Remote Control The following table describes the buttons on the remote control that are for more advanced functions.
The following will explain the function of some of the buttons found on your remote control. To turn the display off, press again.
This projection TV is capable of receiving i, p, p and i digital TV formats note that p is displayed as p. The factory setting for Favorite Channel is Auto. You can also change the size of both the left and right pictures. Page Using the Features Changing the The zoom feature lets you change the size of the left and right pictures. Picture Size To enlarge the left To enlarge the picture reduce right picture the right reduce the left Move the Move the joystick left to joystick right activate the left Suivre ces procedures lors de chaque remplacement de composants critiques, ou lorsqu'un mauvais fonctionnement suspecte.
No revisions or updates are applicable at this time. Updated G Pg. Added critical symbol to G Board on Exploded View section Updated critical components on Parts Lists Pgs. Updated Table of Contents Replace Pg. Replaced Adjustable Service Data Lists. Corrected procedures for Added Corrected 3-D-Comb from Deleted IC Block Diagram from Corrected semiconductors Corrected Grille piece on cover exploded view diagrams Replace Pgs.
Replace History Pg. Removed Note from section Note is intended for use by the factory during. Updated Exploded View section to include new PNs based on serial range. Warnings and Cautions Safety Check-Out Self-Diagnostic Function UD Board Removal Printed Wiring Boards and. Schematic Diagrams Information CR Board Schematic Diagram CB Board Schematic Diagram CG Board Schematic Diagram V Board Schematic Diagram G Board Schematic Diagram UD Board Schematic Diagram A Board Schematic Diagram 1 of A Board Schematic Diagram 2 of A Board Schematic Diagram 3 of U Board Schematic Diagram AD Board Schematic Diagram B Board Schematic Diagram 1 of B Board Schematic Diagram 2 of
0コメント